Vario Case footman loops - BMW R1200GS Forum : R1200 GS Forums
 
LinkBack Thread Tools Display Modes
post #1 of 3 (permalink) Old 07-Oct-2017, 12:10 PM (715) Thread Starter
Senior Member
 
jaxon's Avatar
 
Join Date: May 2017
Posts: 150
Garage
Vario Case footman loops

Short overview of adding footman loops to vario cases.

Note that there is a ideal mounting point on the top of the cases. This area is simply a cover and requires no drilling in the inner case.

The footman loop is 1 inch long. This is the length of the inner loop itself. I got mine here:

Metal Footman Loops

I used an 8/32 Phillips screw 1/2 long and locknuts and washers.

Open the side case.

Remove the Torx screws holding the top panel of each side.

Remove the locking mechanism by removing the 3 Phillips head screws. 1 short screw is in the middle. If anything the actual yellow locking tab may drop out. Hold it in place.

Remove the 2 additional Torx screws under the locking mechanism.

Eyeball the outside top of the case. You need to ensure the lock nut for your 8/32 Phillips screw is outside of the bevel in the inside of the case.
Attached Images
    

--
2017 R1200GS
1992 K75S
2013 G650GS

Last edited by jaxon; 07-Oct-2017 at 12:25 PM (726).
jaxon is offline  
Sponsored Links
Advertisement
 
post #2 of 3 (permalink) Old 07-Oct-2017, 12:20 PM (722) Thread Starter
Senior Member
 
jaxon's Avatar
 
Join Date: May 2017
Posts: 150
Garage
Continued due to attachment limit...

Note the locking nut will be seated in the area were the screwdriver is shown. I also used a washer and a dab of silicon sealant.

You can scuff up the screw head with sand paper and paint it with enamel touchup paint. Might want to do this before you mount the loop. I'm touching them up in the photo.

I elected not to mount a loop on the opposite side since there's plenty on anchor point on the rear rack or simply using Rok Straps across to the other side.

The Vario top case can also accept a footman loop using the same technique. Issue is the opposite site would be a little strange. The area on the opposite side goes near the hinge itself. The opposite side isn't as ruggedly mounted. I'll likely do this later and post the photos.
Attached Images
   

--
2017 R1200GS
1992 K75S
2013 G650GS

Last edited by jaxon; 07-Oct-2017 at 12:29 PM (728).
jaxon is offline  
post #3 of 3 (permalink) Old 07-Oct-2017, 02:16 PM (802)
Senior Member
 
bmwbob51's Avatar
 
Join Date: Jan 2015
Posts: 715
Me Too

I've had a set and still need to install them. Thanks for the over view.
bmwbob51 is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the BMW R1200GS Forum : R1200 GS Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in













Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome